Fabrication and characterization of planar and channel polymer waveguides. III. Compositional distribution and solute loss in polymer thin films

For many microelectronic and optoelectronic applications, polymer thin films require the addition of small molecules. However, the thin‐film geometry and associated processing techniques will influence the final morphology and compositional distribution of the constituents. It is therefore important that these be examined directly rather than inferred from bulk measurements. As an example system, the concentration and distribution of Disperse Red 1 (DR1) molecules in poly(methyl methacrylate) thin films were examined. Ultraviolet visibility spectroscopy and dynamic secondary ion mass spectrometry indicate that the composition of the molecules decreased dramatically with thermal treatment of the film. The sublimation of the chromophore was observed to occur at temperatures well below the melting point of the small molecule and the glass transition of the pure polymer; this solute loss manifested itself in changes in the glass transition temperature of the film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2021–2024, 2002     

Pt-V2O5-WO3/TiO2 catalysts supported on SiC filter for NO reduction at low temperature

The catalytic filter, V₂O₅-WO₃-TiO₂ supported on a ceramic filter, is known as a promising material for treating particulates and NO _x simultaneously at optimum temperatures around 320°C. In order to improve its catalytic activity at low temperatures, the effect of Pt addition on the catalytic filter has been investigated. Catalytic filters, Pt-V₂O₅-WO₃-TiO₂/SiC, were prepared by co-impregnation of Pt, V, and W precursors on TiO₂ coated-SiC filter by vacuum aided-dip coating. The Pt-added catalytic filter shifted the optimum working temperature from 280–330°C (for the non Pt-impregnated filter) to 180–230°C, providing N _x slip concentration less than 20 ppm for the treatment of 700 ppm NO at a face velocity of 2 cm/s with the same value over the non Pt-added catalytic filters. The promotional effect following the addition of Pt is believed to result from electrical modification of the catalyst maintaining a high electron transfer state. Ammonia oxidation was also observed to be dominant above the optimal temperature for SCR.     

Classification of time series by shapelet transformation

Time-series classification (TSC) problems present a specific challenge for classification algorithms: how to measure similarity between series. A shapelet is a time-series subsequence that allows for TSC based on local, phase-independent similarity in shape. Shapelet-based classification uses the similarity between a shapelet and a series as a discriminatory feature. One benefit of the shapelet approach is that shapelets are comprehensible, and can offer insight into the problem domain. The original shapelet-based classifier embeds the shapelet-discovery algorithm in a decision tree, and uses information gain to assess the quality of candidates, finding a new shapelet at each node of the tree through an enumerative search. Subsequent research has focused mainly on techniques to speed up the search. We examine how best to use the shapelet primitive to construct classifiers. We propose a single-scan shapelet algorithm that finds the best $k$ shapelets, which are used to produce a transformed dataset, where each of the $k$ features represent the distance between a time series and a shapelet. The primary advantages over the embedded approach are that the transformed data can be used in conjunction with any classifier, and that there is no recursive search for shapelets. We demonstrate that the transformed data, in conjunction with more complex classifiers, gives greater accuracy than the embedded shapelet tree. We also evaluate three similarity measures that produce equivalent results to information gain in less time. Finally, we show that by conducting post-transform clustering of shapelets, we can enhance the interpretability of the transformed data. We conduct our experiments on 29 datasets: 17 from the UCR repository, and 12 we provide ourselves.     

Authorized workflow schemas: deciding realizability through \mathsf{LTL }(\mathsf{F }) model checking

Many business processes are modeled as workflows, which often need to comply with business rules, legal requirements, and authorization policies. Workflow satisfiability is the problem of determining whether there exists a workflow instance that realizes the workflow specification while simultaneously complying with such constraints. This problem has already been studied by the computer security community, with the development of algorithms and the study of their worst-case complexity. These solutions are often tailored to a particular workflow model and are, therefore, of little or no use in analyzing different models; their worst-case complexities are likely to be an unreliable judge of their feasibility; and they lack support for other forms of analysis such as the determination of the smallest number of users required to satisfy a workflow specification. We propose model checking of an NP-complete fragment $\mathsf{LTL }(\mathsf{F })$ of propositional linear-time temporal logic as an alternative solution. We report encodings in LTL(F) that can compute a set of solutions (thus deciding satisfiability), compute minimal user bases and a safe bound on the resiliency of satisfiability under the removal of users. These theoretical contributions are validated through detailed experiments whose results attest to the viability of our proposed approach.     

Fabrication of patterned porous silicon using high-energy ion irradiation

P-type silicon has been patterned using high-energy protons beam prior to electrochemical etching in hydrofluoric acid. The ion beam selectively damages the silicon lattice, resulting in an increase in the local resistivity of the irradiated regions. It is found that the photoluminescence intensity of the irradiated regions increases with proton irradiation into a 0.02 Ω.cm resistivity p-type silicon. By immersing the etched sample into potassium hydroxide, the porous silicon is removed to reveal the underlying three-dimensional structure of the patterned area.     

Decadienoates: Sex Pheromone Components of Nettle Caterpillars Darna trima and D. bradleyi

This study was undertaken to identify sex pheromone components of nettle caterpillars Darna trima and Darna bradleyi (Lepidoptera: Limacodidae) whose larvae defoliate oil palm, Elaeis guineensis, in southeast Asia. Coupled gas chromatographic–electroantennographic detection (GCEAD) analyses of pheromone gland extracts revealed two antennally active compounds produced by female D. trima and two by female D. bradleyi. Molecular structures of these candidate pheromone components were identified by electron-impact and chemical-ionization mass spectrometry; retention-index calculations on DB-5, DB-23, and DB-210 columns; microanalytical treatments, as well as syntheses of "auxilliary" compounds that facilitated identification of the compounds. The compounds from D. trima were 2-methylbutyl (E)-7,9-decadienoate (A) and (E)-2-hexenyl (E)-7,9decadienoate (B); from D. bradleyi we identified methyl (E)-7,9-decadienoate (C), and isobutyl (E)-7,9-decadienoate (D). In field experiments in Malaysia, (S)-2-methylbutyl (E)-7,9-decadienoate (SA) in combination with B proved to be essential and synergistic pheromone components for attraction of male D. trima. (R)-2-Methylbutyl (E)-7,9-decadienoate (RA) had no behavioral activity. Compound D singly attracted male D. bradleyi, but addition of C to D at a 1 : 10 ratio significantly enhanced attractiveness of the bait. Synthetic pheromone blends were more effective trap baits than unmated female moths and could be developed for monitoring populations of D. trima and D. bradleyi in Asian oil palm plantations.     

Associations between apolipoprotein E genotype and circulating F<Subscript>2</Subscript>-isoprostane levels in humans

Apolipoprotein E (apoE), an important determinant of plasma lipoprotein metabolism, has three common alleles (ε2, ε3, and ε4). Population studies have shown that the risk of diseases characterized by oxidative damage, such as coronary heart disease and Alzheimer’s disease, is significantly higher in ɛ4 carriers. We evaluated the association between apoE genotypes and plasma F₂-isoprostane levels, an index of lipid peroxidation, in humans. Two hundred seventy-four healthy subjects (104 males, 170 females; 46.9±13.0 yr; 200 whites, 74 blacks; 81 nonsmokers, 64 passive smokers, and 129 active smokers) recruited for a randomized clinical antioxidant intervention trial were included in this analysis. ApoE genotype was determined by PCR and restriction enzyme digestion. Free plasma F₂-isoprostane was measured by GC-MS. Genotype groups were compared using multiple regression analysis with adjustment for sex, age, race, smoking status, body mass index, plasma ascorbic acid, and β-carotene. Subjects with ε3/ε4 and ε4/ε4 genotype (ε4-carriers) and with ε2/ε3 and ε3/ε3 (non-ε4-carriers) were pooled for analysis. In subjects with high cholesterol levels (total cholesterol above 200 mg/dl), plasma F₂-isoprostane levels were 29% higher in ε4 carriers than in non-ε4-carriers (P=0.0056). High-cholesterol subjects that are ε4 carriers have significantly higher levels of lipid peroxidation as assessed by circulating F₂-isoprostane levels.     

Hydrocarbon condensation modelling to mitigate fluid coker cyclone fouling

FLUID COKING is a continuous process that thermally converts heavy hydrocarbons, such as oil sands bitumen, to lighter and higher‐value products by horizontal spray injection onto a fluidized bed of hot coke particles. The cyclone sections of commercial fluid coker reactors experience fouling during typical operation, which limits unit run lengths. The main objective of this work is to improve fluid coker reliability by proposing cyclone fouling mitigation strategies based on practical operation modifications. This study developed a process simulation in Aspen Plus to establish the combined impact of vapour‐liquid equilibrium, endothermic thermal cracking reactions, pressure changes, and overall fluid dynamics in the selected fluid coker control volumes. The hydrocarbon composition was defined by applying an assay characterization of distillation data for representative hydrocarbon streams. Case studies were performed to determine the sensitivity of the predicted temperatures and hydrocarbon condensate flow rates for: (a) the burner‐to‐fluid coker transfer line temperature; (b) the hot coke flow rate; (c) hot coke entrainment from the freeboard region; and (d) scouring coke flow rate in the horn chamber. The scouring coke flow rate was identified as the most promising process lever to mitigate fluid coker cyclone fouling.     

Microstructure and tensile properties of squeeze cast magnesium alloy AM50

High-pressure die cast magnesium alloy AM50 is currently used extensively in large and complex shaped thin-wall automotive components. For further expansion of the alloy usage in automobiles, novelmanufacturing processes need to be developed. In this study, squeeze casting of AM50 alloy with a relatively thick cross section was carried out using a hydraulic press with an applied pressure of 70 MPa. Microstructure and mechanical properties of the squeeze cast AM50 with a cross-section thickness of 10 mm were characterized in comparison with the die cast counterpart. The squeeze cast AM50 alloy exhibits virtually no porosity in the microstructure as evaluated by both optical microscopy and the density measurement technique. The results of tensile testing indicate the improved tensile properties, specifically ultimate tensile strength and elongation, for the squeeze cast samples over the conventional high-pressure die cast parts. The analysis of tensile behavior show that the strain-hardening rate during the plastic deformation of the squeeze cast specimens is constantly higher than that of the die cast specimens. The scanning electron microscopy fractography evidently reveals the ductile fracture features of the squeeze cast alloy AM50.     

Coordination arrival control for multi‐agent systems

The coordination arrival problems of first‐order multi‐agent systems with the arriving structure and the time structure requirements are considered for the cases with no obstacle and obstacle. To describe the distributed coordination arrival problems, we first introduce needed definitions, such as coordination arrival, threat point, and arrival structure. By selecting the estimated value of the arriving time of the agent as variable, we then develop a central estimating algorithm, which is used to construct the arriving protocols. Based on the estimating algorithm, we build and analyze coordination arriving protocols for the proposed coordination arrival problems. Several simulation examples are presented to validate the proposed algorithms. Copyright © 2015 John Wiley & Sons, Ltd.